Fedora 17 Installation Guide
amd catalyst 12.6 beta can work well with fedora 17. http://support.amd.com/us/kbarticles/Pages/AMDCatalyst126beta.aspx
Steps to install:
1. You need kernel 3.3.7-1 or 3.3.7-3 . Get them from: (Download kernel, kernel-devel and kernel-headers)
Kernel 3.3.7-3: http://koji.fedoraproject.org/koji/buildinfo?buildID=321331 Kernel 3.3.7-1: http://koji.fedoraproject.org/koji/buildinfo?buildID=319972
2. Amd Catalyst 12.6 beta from: http://support.amd.com/us/kbarticles/Pages/AMDCatalyst126beta.aspx
Even if you have kernel 3.4.0-1 or higher, this procedure will work! So dont panic! I will take kernel 3.3.7-3 as example, you can use 7-1.
1. Install the kernel: sudo yum --nogpgcheck install kernel-3.3.7-2.fc17.x86_64.rpm (nogpgcheck is needed sice koji packages are not signed)
2. Remove existing kernel-devel: First do: rpm -qa | grep kernel-devel . Then remove the kernel-devel-3.x.x package you see, by using yum erase kernel-devel-3.4.0-1.fc17.x86_64 (or whatever package you are using)
3. Install kernel-devel sudo yum --nogpgcheck install kernel-3.3.7-2.fc17.x86_64.rpm
4. Now, you need to remove kernel-headers. You need to use rpm, sice yum wont uninstall it because of dependancies. Use: rpm -evv -nodeps kernel-headers-220.127.116.11.fc17.x86_64 (or your kernel headers version, check with rpm -qa | grep kernel-headers)
5. Reboot to kernel 3.3.7-3 and install AMD-ATI Catalyst 12.6 BETA driver.
6. now edit yum.conf and exclude kernel updates. do: sudo nano /etc/yum.conf and add this to the end: "exclude=kernel*" This will prevent kernel from upgrading. When a new version of Catalyst is available, check for the kernel it supports and upgrde your kernel by uncommenting this line.
If you have an HD4xxx series card, Catalyst 12.4 is the newest driver to support it (as of June 4, 2012). This won't work with X version 1.12 (the one packaged with Fedora 17). To downgrade to X version 1.11, use the following commands (as root).
Note: I'm assuming x86_64
IMPORTANT: I'd highly recommend going down to runlevel 3 first. You can do this using the following command in one of the text consoles (<CTRL> + <ALT> + <Fx> where x is 1-9, just try them until you get to a console)
systemctl isolate runlevel3.target
Commands for downgrading X:
yum erase xorg-x11-drv-intel
yum --releasever=16 install libxcb* xcb-util startup-notification*
yum --releasever=16 downgrade *xcb* xorg*
You may also need libxcb.i686 from the Fedora 16 release. The intel driver has additional dependencies, and those with AMD/ATi cards don't need it anyway.To solve the issues with the new kernel source, use the steps in
3.4.0 has been pushed as the most recent kernel update. This will require recompiling the drivers in addition to commenting the two lines out of
uaccess_64.h. Make sure you've rebooted into the new kernel before compiling the driver. To compile go to the directory where the
amd-driver-installer-12-4-x86.x86_64.run file is and type:
./amd-driver-installer-12-4-x86.x86_64.run --extract fglrxYou will then need to edit
./fglrx/common/lib/modules/fglrx/build_mod/kcl_ioctl.cand add the line
DEFINE_PER_CPU(unsigned long, old_rsp);on line
220directly under the end of the multi-line comment. You also need to edit line
for_each_possible_cpu(p). After this, execute
./fglrx/common/lib/modules/fglrx/build_mod/make.shas root. If you get an error about no make target for
libfglrx_ip.a, then copy the one from
./fglrx/common/lib/modules/fglrx/build_mod/and try again. Finally, run
./fglrx/common/lib/modules/fglrx/make_install.shas root then
rebootto check your results, which I do by seeing if this command correctly outputs a temperature.
aticonfig --adapter=0 --od-gettemperature