Fedora 8 Installation Guide: Difference between revisions

From cchtml.com
m (Protected "Fedora 8 Installation Guide": Excessive vandalism ([edit=autoconfirmed] (expires 14:02, 24 December 2012 (UTC)) [move=autoconfirmed] (expires 14:02, 24 December 2012 (UTC))))
 
(9 intermediate revisions by 5 users not shown)
Line 7: Line 7:
and restart your system.
and restart your system.


> I did have a few problems, molsty things that were from non-fedora repositories.> [...]> Another is that I love to use vlc, but its in the livna repository and currently> requires python 2.4, but Werewolf uses python 2.5That sounds to me as if you did something wrong  vlc in livna devel works fine on Fedora devel (which F8 still officially is). IOW: you have to use the Livna devel repos is you use Fedora Devel (what will become Fedora 8). Then vlc should work and updates should be smooth for those packages that you got from livna earlier, as livna provides up2date packages that work on rawhide.
==Installation Option #2 Livna repository==
rpm -ivh http://rpm.livna.org/livna-release-8.rpm
* [http://www.fedorafaq.org/#radeon These instructions] on the Unoffical Fedora FAQ work. (In order not to duplicate the the instructions, we provide the link rather than the instructions themselves).


==Installation Option #3 via ATI Installer==
==Installation Option #3 via ATI Installer==

Latest revision as of 14:02, 10 December 2012

General Status

  • Supported since Catalyst 7.11, which adds support for kernel 2.6.23.

Installation Option #1 Freshrpms.net repository

rpm -ihv http://ftp.freshrpms.net/pub/freshrpms/fedora/linux/8/freshrpms-release/freshrpms-release-1.1-1.fc.noarch.rpm
yum install -y ati-x11-drv

and restart your system.

Installation Option #2 Livna repository

rpm -ivh http://rpm.livna.org/livna-release-8.rpm
  • These instructions on the Unoffical Fedora FAQ work. (In order not to duplicate the the instructions, we provide the link rather than the instructions themselves).

Installation Option #3 via ATI Installer

You can get the latest ATI-Driver here:

Linux Driver

The above bugzilla contains a patch to the firegl module source code. Here is an annotated walk-through for those not familiar with using the patch utility:

  • Install the driver interactively
sh ./ati-driver-installer-8.42.3-x86.x86_64.run
  • Backup the existing module, download the patch
cd /lib/modules/fglrx/build_mod/
cp firegl_public.c firegl_public.c.orig
wget -qO- http://ati.cchtml.com/attachment.cgi?id=466 > firegl.patch
  • Apply the patch
patch -p0 < firegl.patch
  • Now build and install the kernel module
./make.sh
cd .. ; ./make_install.sh
  • Create an initial X Server configuration file
aticonfig --initial
  • Restart your X Server (by logging out/in or rebooting)

Issues

FYI: this patch (and others like it) is incomplete. It fails miserably with the drm module loaded. It will not work without drm either, and what would be the point? As seen by dmesg:

[drm] Initialized drm 1.1.0 20060810
[fglrx] Maximum main memory to use for locked dma buffers: 1898 MBytes.
[fglrx] ASYNCIO init succeed!
[fglrx:KCL_enable_pat] *ERROR* Pat entry 2 is already configured
[fglrx] PAT is disabled!
[fglrx:firegl_init_module] *ERROR* firegl_stub_register failed

The livna rpm incurs the same failure. Stick with F7 and kernel 2.6.22, or use the radeon driver instead.


Updated by yangyud:
You need to remove the loaded "drm" module from kernel before install the fglrx module.
rmmod radeon; rmmod drm

See Also

Ok, the problem is gdm. I can `startx`, but gdm fails to load with fglrx, and there is no indication in any log as to why. This continues with new 7.11 Catalyst driver. Because of this, the problem is NOT with the driver, rather it is the default GDM time value of 10-seconds. To remedy:

vi /etc/gdm/custom.conf

[daemon]
GdmXserverTimeout=60

This allows enough time for X to startup before gdm considers it dead and aborts the X startup process.