Ubuntu Gutsy Installation Guide

From cchtml.com
Revision as of 16:52, 15 November 2007 by Mooninite (talk | contribs) (Reverted edits by Mooninite (Talk); changed back to last version by 147.162.118.141)

The latest fglrx driver supports Radeon 9500 and the X-series cards up to HD2900. Workstation cards are not supported.

Pre-Installation Checks

Enable "restricted" Repository

Make sure the restricted repository is enabled in /etc/apt/sources.list or this guide will not work!

System > Administration > Software Sources. Check "Proprietary Drivers for Devices (Restricted)" box.

Installation

For most users it won't be necessary to go into installation and configuration details of the driver. Ubuntu 7.10 (Gutsy) provides a notification saying that there are restricted drivers available. You just have to go there (Restricted Drivers Manager) and enable the "ATI accelerated graphics driver". Ubuntu will then install and configure the driver for you. If this does not provide the optimal solution you were looking for, please read ahead.

Method 1: Install the Driver the Ubuntu Way

sudo apt-get update	
sudo apt-get install linux-restricted-modules-generic restricted-manager
sudo apt-get install xorg-driver-fglrx
sudo depmod -a

Note: The second line of the above may not be necessary. If apt says it cannot find the "linux-restricted-modules" package, try line 3. If that fails, check your sources.list (see top of page)

If the system complains about dependencies, use your preferred package manager to download python2.4 and, if necessary, its dependencies.

(Note: This method did not work with ATI X1300 Radeon on Gutsy whereas method 2 worked perfectly for us. 26/10/2007)

Method 2: Install the 8.42.3 Driver Manually

  • Note: This is just an alternative installation method for the section above. It might help if you still get 'DRI missing' errors.
  • Note: If you are running the -rt kernel, you will fail to compile the kernel module with "FATAL: modpost: GPL-incompatible module fglrx.ko uses GPL-only symbol '__rcu_read_lock'".

Download the ATI driver installer: ati-driver-installer-8.42.3-x86.x86_64.run (this installer is for 32bit and 64bit systems)

Change to the download directory. Make sure that you have the universe and multiverse repositories enabled in /etc/apt/sources.list before doing these steps.

There is a detailed manual with screenshots at Ubuntu Wiki.

By default, Ubuntu did not enable the Universe and Multiverse repositories, but now in Gutsy, both Universe and Multiverse are activated by default.

Install necessary tools:

sudo apt-get update
sudo apt-get install module-assistant build-essential fakeroot dh-make debhelper \
debconf libstdc++5 linux-headers-generic

Create .deb packages:

(don't use fakeroot ,"fakeroot: nested operation not yet supported")

sudo bash ati-driver-installer-8.42.3-x86.x86_64.run --buildpkg Ubuntu/gutsy

Blacklist old fglrx module from linux-restricted-modules:

As Ubuntu Gutsy's linux-restricted-modules package includes the fglrx module from an old driver version (8.37.6), we have to blacklist this module to make sure the new kernel module which is needed by the new driver will be used instead.

Ubuntu/Gnome users type in:

gksu gedit /etc/default/linux-restricted-modules-common

Kubuntu/KDE users type in:

kdesu kate /etc/default/linux-restricted-modules-common

Add "fglrx" to the line "DISABLED_MODULES"

File: /etc/default/linux-restricted-modules-common
DISABLED_MODULES="fglrx"


Install .deb packages:

sudo dpkg -i xorg-driver-fglrx_8.42.3-1*.deb \
fglrx-kernel-source_8.42.3-1*.deb \
fglrx-amdcccle_8.42.3-1*.deb
  • Note: If you get a 'Bad file descriptor' message concerning the xorg.conf file try switching user to root and repeating the same command without sudo. This might be valid for the following commands too. (Ubuntu Gutsy installs with no password set for root by default. You can set a password for the root by typing 'sudo passwd root' first.)
  • Note: If you have a 64 bit install, the above dpkg command will likely complain that "Errors were encountered while processing: fglrx-amdcccle". This is because of a dependency of the amdccle package on 32 bit libraries. If you recieve this error, issue the following command after the above dpkg command, which will force the installation of all of the 32 bit dependencies, and then the amdccle pacakge:
sudo apt-get install -f


Remove any old fglrx debs from /usr/src/:

sudo rm /usr/src/fglrx-kernel*.deb

Fix broken dependencies

  • Note: You only need to do this if you have installed previous versions of these drivers using this method before.
sudo apt-get -f install

Compile the kernel module:

sudo module-assistant prepare,update
sudo module-assistant build,install fglrx -f
sudo depmod -a

It's necessary, because sometimes this file is written by other packages, and so there's no 3D acceleration. Check that the file /lib/modules/$(uname -r)/misc/fglrx.ko has been created.

Create the following folder

sudo mkdir /lib/modules/$(uname -r)/volatile

Note: the volatile directory might already exist at this stage then simply continue with the next step.

Create a symbolic link

sudo ln -sf /lib/modules/$(uname -r)/misc/fglrx.ko /lib/modules/$(uname -r)/volatile/fglrx.ko


NOTE : On my Gutsy install, after a reboot this link was always removed automatically leaving me without an fglrx module loaded, and thus no ATI rendering. There have been several ways of getting around this suggested here, but my experience with recent installs and updates still leads to a MESA driver being installed. This became very frustrating as I tried every method and step here with no success. A new way around this is to let the old MESA fglrx load, then as a final step in the boot process, edit rc.local :

sudo gedit /etc/rc.local

copy these two line at the beginning of the file right on top of the command "set 0" :

rmmod fglrx
insmod /lib/modules/$(uname -r)/misc/fglrx.ko

This removes the Ubuntu fglrx module in the first line, and then the second line loads the newly installed one. This should now force the ATI module in and you should get the correct results in the following steps.

IMPORTANT: You have to recompile the kernel module after each kernel update! (Note: This does not affect you until the next time you update your kernel.)

Configure the Driver

  • Note Method 2 Users: Before you carry out this step you must reboot your machine. Or else the fglrx driver will not be in use on xorg.conf and using the aticonfig options will cause a memory dump and not intialise the Driver properly.
  • Note: An alternative to the aticonfig --initial command is to edit /etc/X11/xorg.conf and replace the string "ati" with "fglrx" in the "Device" section. This way you won't lose your old "Screen" and "Monitor" settings. Afterwards you can use aticonfig for setting overlay etc. Another alternative is aticonfig --initial --force if you encounter issues with the first command.
sudo aticonfig --initial

Then:

sudo aticonfig --overlay-type=Xv
  • Note: Is there an alternative to the previous step?

Finish the Installation

Now save any open document and reboot your system:

sudo shutdown -r now
  • Note: An alternative to rebooting is to restart the X Server by pressing your CTRL ALT BACKSPACE keys. You must remove any old kernel modules such as "drm" "radeon" or "fglrx" using the "rmmod" command. Example: sudo rmmod fglrx

Post-Installation Checks

Verifying

Run the following command to check its output to ensure the fglrx driver is installed properly:

$ fglrxinfo
display: :0.0  screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI Radeon Xpress Series
OpenGL version string: 2.0.6958 Release

Download this: fglrx-8.42-ubuntu+debian-2.tar.bz2

Extract the installer:

bash ati-driver-installer-8.42.3-x86.x86_64.run --extract somedirectory

Extract the archive you downloaded to the directory that you extracted the driver's installation files to.

Then build the package:

./ati-installer.sh 8.42.3 --buildpkg Ubuntu/gutsy

Revert to Xorg driver

If (for any reason) the fglrx install fails, you can revert to the Xorg driver by executing

sudo dpkg-reconfigure xserver-xorg

and selecting the "ati" driver, or simply restoring the previous /etc/X11/xorg.conf file, if you made a backup.

You also need to remove the xorg-driver-fglrx or your manually installed drivers to get the 3D acceleration back, since it is provided by file /usr/lib/libGL.so.1.2 which belongs to libgl1-mesa package and which is moved to backup and replaced at the installation of xorg-driver-fglrx (or the manually built) package. In case the removal of the fglrx drivers fails to restore the file from libgl1-mesa, you have to reinstall the package by running:

sudo apt-get install --reinstall libgl1-mesa

Attention: Suspend/Hibernation will not work

With Gutsy release, there's a big problem using the ATI proprietary drivers. The Suspend/Hibernate function will stop working. The problem is due to the new SLUB allocator incorporated in 2.6.22 / 2.6.23 Kernel. There are no workaround, except:

- Return to Feisty (with 2.6.20 kernel, and apply specific solutions: see Feisty installation guide).

- Use default Mesa Drivers (the easiest way is to disable ATI driver from Restricted Driver Manager).

- Recompiler your Kernel to use SLAB.

Unfortunately some new ATI cards couldn't start X with Mesa drivers, so the only workaround is returning to Feisty.

The problem will be solved in the next ATI driver release.

If you get /usr/X11R6/lib/modules/dri/fglrx_dri.so not found

sudo ln -s /usr/lib/ /usr/X11R6/lib/modules

libGL error

  • fglrxinfo gives: libGL.so.1: cannot open shared object file.
  • Fixed with command:
sudo ln -s /usr/lib/libGL.so.1.2 /usr/lib/libGL.so.1

See Also