cchtml.com - User contributions [en]

Ubuntu Intrepid Installation Guide

2009-03-10T18:05:49Z

65.67.98.193: /* Installing the proprietary drivers "the ATI way" */

= Installation Guide for Ubuntu Intrepid (v 8.10) =

== The alternatives ==

ATI has a bad track-record when it comes to drivers for Linux. There are countless stories about black screens, hours of configuring X, installing drivers and swearing at the computer.
AMD has traditionally been a bit more Linux-friendly, so after AMD bought ATI, a slight hope has arisen for better drivers for ATI-cards on Linux.

However, creating better drivers takes some time, so while the people at AMD are doing their thing, people with ATI cards basically have these options:
# Use the open source drivers. These are stable and nice, but currently they have poor 3D-performance, if any. If that's not a problem, they are the Right Choice (tm).
# Use the restricted-driver management system that comes with Ubuntu to install the drivers (envy/jockey/"restricted" packages).
# Install the proprietary drivers as made available by AMD.
# Install the drivers manually. This should be your last resort, and may not even work.

= The open source drivers =
By default, one of the open source drivers are used. If this works for you, you don't need to change anything.

These come with the X.org X server:
* vesa
* ati
* radeon
* radeonhd

The "ati" driver will automatically choose the best driver for your video card. There is no need to change it from "ati" or even create an xorg.conf file in most cases. The xorg.conf file is being deprecated.

= Installing the restricted drivers "the Ubuntu way" =

== Restricted Drivers Manager ==
For most users it won't be necessary to go into installation and configuration details of the driver. Ubuntu 8.10 (Intrepid) provides a notification saying that there are restricted drivers available. You just have to go there (Restricted Drivers Manager) and enable the "ATI accelerated graphics driver". Ubuntu will then install and configure the driver for you.

== Post-Installation Tweaks ==
To enable hardware accelerated video on pre-R500 cards, edit '''/etc/X11/xorg.conf''' to include the following lines without '''[...]'''

<pre>
Section "Device"
[...]
Driver "fglrx"
Option "VideoOverlay" "on"
Option "OpenGLOverlay" "off"
[...]
EndSection
</pre>

Note that when Visual Effects (Compiz) are active, flickering and artifacts may occur in OpenGL applications and hardware accelerated video windows (particularly with R300 chipset). To prevent this, disable Visual Effects.

= Installing the proprietary drivers "the ATI way" =
Download the Cataylst {{Catalystversion}} AMD driver file and run the installer. People that have not had luck with the first two choices have had success with this.

= Installing the restricted drivers manually =
''If you are using the x86_64 architecture (64 bit), be sure to inst "ia32-libs" before proceeding!''

Make sure ''universe'' and ''multiverse'' are enabled in your repository sources.

===''Before you start''===
Install the necessary programs
{{Box Terminal|
sudo apt-get install build-essential cdbs fakeroot dh-make debhelper debconf libstdc++5 dkms
}}

===''1. Download the latest Catalyst package.''===

Download page: Catalyst {{catalystversion}}. This package contains both the 32-bit and 64-bit driver.

Open a terminal window and switch to the directory you downloaded the installer to. (Example: $ cd Desktop)

Make sure your directory path does not contain spaces

===''2. Create .deb packages.''===
{{Box Terminal|
sh {{catalystfilename}} --buildpkg Ubuntu/intrepid
}}

===''3. Install .debs.''===
For 32-bit systems

{{Box Terminal|
sudo dpkg -i xorg-driver-fglrx_8.582-0ubuntu1_i386.deb fglrx-kernel-source_8.582-0ubuntu1_i386.deb fglrx-amdcccle_8.582-0ubuntu1_i386.deb
}}

(This may fail due to a missing dpmk. If so install this first)

or for 64-bit systems

{{Box Terminal|
sudo dpkg -i xorg-driver-fglrx_8.582-0ubuntu1_amd64.deb fglrx-kernel-source_8.582-0ubuntu1_amd64.deb fglrx-amdcccle_8.582-0ubuntu1_amd64.deb
}}
''Using [http://en.wikipedia.org/wiki/Command_line_completion tab completion] can make this command easier.''

== Additional 64-bit instructions ==

If you have a 64 bit install, the above dpkg command may complain that "Errors were encountered while processing: fglrx-amdcccle". This is because of a dependency of the amdccle package on 32 bit libraries. If you receive this error, issue the following command after the above dpkg command, which will force the installation of all of the 32 bit dependencies, and then the amdcccle package:

{{Box Terminal|
sudo apt-get install -f
}}

Catalyst {{catalystversion}} on 64-bit systems requires the ''--force-overwrite'' command in the above ''dpkg'' command:
{{Box Terminal|
sudo dpkg -i --force-overwrite xorg-driver-fglrx_8.582-0ubuntu1_amd64.deb fglrx-kernel-source_8.582-0ubuntu1_amd64.deb fglrx-amdcccle_8.582-0ubuntu1_amd64.deb
}}
''Using [http://en.wikipedia.org/wiki/Command_line_completion tab completion] can make this command easier.''

== Finishing the Install: Configuration ==

'''If you've used fglrx previously, you will not need to do this.'''

Now you'll have to edit your xorg.conf

For Ubuntu:
{{Box Terminal|
sudo gedit /etc/X11/xorg.conf
}}

For Kubuntu:
{{Box Terminal|
sudo kate /etc/X11/xorg.conf
}}

and add the following line to the Device section (if it does not already exist). Include the following lines without '''[...]''':
<pre>Section "Device"
[...]
Driver "fglrx"
[...]
EndSection</pre>
Save and exit, then run
{{Box Terminal|
sudo aticonfig --initial -f
}}
in a terminal. If it doesn't give an error you should be good.

Some people find that changes to xorg.conf don't get used by the driver. To force the ati driver to adopt changes made to xorg.conf, type the following command:

{{Box Terminal|
sudo aticonfig <nowiki>--input=/etc/X11/xorg.conf --tls=1</nowiki>
}}

Finally, reboot the computer and type
{{Box Terminal|
fglrxinfo
}}
into the terminal. If the vendor string contains ATI, you have installed the driver successfully. Release 8.12 looks like:
<pre>
display: :0.0 screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI Radeon HD 3850
OpenGL version string: 2.1.8304 Release
</pre>

Release 9.2 looks like:
<pre>
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: ATI Radeon HD 4670
OpenGL version string: 2.1.8494 Release
</pre>

Please note: Depending on the particular ATI card that you own, you may or may not automatically have all of the relevant driver features enabled. R500 and R600 cards (X1xxx, HD series, and newer) in particular will need TexturedVideo enabled in Xorg.conf (rather than the traditional VideoOverlay) in order to support Xv accelerated video playback.

== Finally ==
# Add tweaks as needed: http://ubuntuforums.org/showthread.php?t=849422
# Restart X, if it doesn't work, you can use the "vesa", "radeon" or "radeonhd" driver in the mean time, until you make it work.
# If you downgraded X to make fglrx work: enter synaptic, make sure all packages with "xorg" and "x11" are locked so that you can update and upgrade without worries.

Done! Now run amdcccle, glxgears, nexuiz, warsow etc :)

= Issues =

== Mesa drivers ==
If fglrxinfo reports that Indirect rendering by Mesa is in place, even though you have installed ATI driver, you might want to remove Mesa:

*Remove the package xserver-xgl.
:<pre>sudo apt-get remove xserver-xgl</pre>
:'''Explanation:''' If you installed this previously in order to make compiz work, it will not allow direct rendering on your display. You can check out if this is what it causing the problem by running
:<pre>DISPLAY=:0 glxinfo | grep render</pre>
:If it returns an ATI renderer, it means that xgl is being displayed indirectly on the display 1. (Taken from [http://ubuntuforums.org/showthread.php?t=740287])

:'''Warning:''' This might make your compiz stop working as it is configured to use XGL. A solution might be to run the Envy script in order to configure compiz. Or, if Compiz stopped working due to "Composite" problem, check that the following is set in the /etc/X11/xorg.conf
<pre>
Section "Extensions"
Option "Composite" "Enable"
EndSection
</pre>

----

*Check for AGP and DRI errors in /var/log/Xorg.0.log like these are:
:(EE) fglrx(0): [agp] unable to acquire AGP, error -1023
:(EE) fglrx(0): cannot init AGP
:(EE) fglrx(0): atiddxDriScreenInit failed, GPS not been initialized.
:(WW) fglrx(0): * DRI initialization failed! *

:If you have Intel 8285P and E7205 chipsets and AGP not detected then you have to remove the i82875p_edac module and restart a some others:
<pre>rmmod i82875p_edac
rmmod fglrx
rmmod intel-agp
rmmod agpgart
modprobe agpgart
modprobe intel-agp
modprobe fglrx</pre>

:Blacklist the modules e7xxx_edac so it doesn't start up again when booting - add the following line at the beginning of /etc/modprobe.d/blacklist:
:<pre>blacklist i82875p_edac</pre>

:This has been known to fix issues with -Mesa -AGP -DRI -Google earth and -suspend to RAM (s2ram).

:'''Explanation:''' http://openwetware.org/wiki/Computing/Linux/Ubuntu

----

*Check you are running the correct kernel.
:'''Explanation:''' If you're upgrading from Gutsy to Hardy in some instances the Grub bootloader does not get updated and the new kernel is not loaded.
:Run in a terminal:
:<pre>uname -r</pre>
:If the output starts with 2.6.22 or below you are not using the current kernel and the Ati drivers will not load properly.

If this doesn't help, try [[Ubuntu Gutsy Installation Guide#Verifying]], or other links: [http://wiki.cchtml.com/index.php/Troubleshooting#No_3D_acceleration], [http://www.thinkwiki.org/wiki/Problems_with_fglrx#Perpetual_Mesa_GLX_Indirect_on_Debian], [http://ubuntuforums.org/archive/index.php/t-475699.html].

== Hang at logout ==

If you experience hangs when logging out (of X) it is probably due to the /etc/ati/authatieventsd.sh script looking for X authorisation files in the wrong place when it starts up. You can kill the hanging authatieventsd.sh processes from a console tty to allow the shutdown of the X server. This can be fixed permanently with:

<pre>sudo mkdir -p /var/lib/xdm/authdir
sudo ln -s /var/run/xauth /var/lib/xdm/authdir/authfiles</pre>

If that doesn't work then you can disable atieventsd with this command:

<pre>sudo /usr/sbin/update-rc.d -f atieventsd remove</pre>

Before the above commands verify that /etc/ati/authatieventsd.sh exists after build and install, if not just do :
(assuming that the installer is in your home directory)

<pre>sh ati-driver-installer-8-12-x86.x86_64.run --extract driver</pre>

<pre>sudo cp ~/driver/packages/Ubuntu/dists/intrepid/replacements/authatieventsd.sh /etc/ati/authatieventsd.sh</pre>

(intrepid is to be replaced by the name used at the building stage (hardy,8.10,8.04,etc...)

<pre>sudo chmod +x /etc/ati/authatieventsd.sh</pre>

just reboot login and ctrl+alt+backspace to try

== Suspend/Hibernation ==

Suspend hibernation '''works''' with the latest driver.

For ATI X1400, to get the laptop to wake up from suspend, I had to change the following in /etc/default/acpi-support:

<pre>
SAVE_VBE_STATE=false

POST_VIDEO=false

ENABLE_LAPTOP_MODE=false
</pre>

<blockquote>
Comment: This is a little surprising, since the comments at the beginning of /etc/default/acpi-support seem to make it quite clear that those settings are ignored unless you add "acpi-support" to SUSPEND_METHODS. --[[User:Bewst|Bewst]] 23:22, 19 December 2008 (UTC)
</blockquote>

For Radeon 3200, to wake up from suspend, I had to add the following lines to /etc/X11/xorg.conf:
(This settings is not good option, if you are using compiz-fusion or any other transparency-based thingie. Not working for HD 3850)

<pre>
Section "Extensions"
Option "Composite" "Disable"
EndSection

Section "ServerFlags"
Option "AIGLX" "off"
EndSection
</pre>

A second Radeon 3200 suspend/wake issue seems to be related to the mouse/keyboard itself. Adding a reset to the kernel line of your grub configuration seems to solve this. In other words, update /boot/grub/menu.lst and add an i8042.reset:

<pre>
kernel /boot/vmlinuz-2.6.27-11-generic root=UUID=73293ec3-5ee4-418c-914
4-1457914fb284 ro quiet splash i8042.reset
</pre>

== Can't remove fglrx with dpkg ==

If dpkg really-really refuses to remove an older fglrx-package, it might be needed to edit /var/lib/dpkg/diversions and remove a few lines. This is a hack and should be avoided.

== This module/version combo is already installed ==

If you get this error-message, simply uninstall the previous version before installing the new one with:
{{Box Terminal|
sudo dkms remove -m fglrx -v 8.522 --all
}}

== New kernel installed? ==
I found out that when getting a new kernel the fglrx kernel-module is not installed for your new kernel.
You can do that by these simple steps:
{{Box Terminal|
sudo dkms build -m fglrx -v 8.552 -k `uname -r` 
sudo dkms install -m fglrx -v 8.552 -k `uname -r`
}}
[[Category:Installation Documentation]]
== AMD Control Center ==
You can start the AMD Control Center by typing:
{{Box Terminal|
amdcccle
}}
If amdcccle doesn't work and says Identifier is not a valid word, this may be caused by some of the reasons below: 
- Use lower case letter in xorg.conf. 
- Make sure lines have no hard returns in them causing some parameters without their corresponding keywords are misinterpreted 
- If amdcccle complains about some keyword in your xorg.conf and quits with a segmentation fault, you may just be working with a different xorg.conf than your system uses. I had a copy of some generic xorg.conf in my home directory, and amdcccle complained about stuff it couldn't cope with. You need to start amdcccle in your /etc/X11 directory.

Talk:Fedora

2007-09-11T13:54:39Z

65.67.98.193:

I was able to install fglrx in fc-6. I'm using Radeon AIW X800XT AGP. The current rpm build was successful; apparently, ATi has fixed that. Running the download with sh from ATi yielded the kernel rpm, the fgrlx rpm, the devel rpm, and the control panel rpm. I ran the kernel rpm, then the fglrx rpm, then the control panel rpm. I didn't run the devel rpm. I now get multiple resolutions up to native 1280X1024 for my 19" LCD and up to 75hz and tv-out. Before, all I got was 800X600 and 640X480 at 60hz and 56hz with corrupted tv-out. I'm a happy camper today! I know the linux purists hate fglrx, but, as is too often the case, they don't yet have good solutions; for one thing, GATOS progress seems to be crawling--they only support cards in the 9200 era.

I may sound preachy and even off-base, but it seems the purists desire for us to be docile hostages, waiting years for them to resolve their showdowns with hardware vendors. The thing is that we who are involved with UNIX are mavericks at heart--generally, we are not docile--we like Linux, but we want Linux that works with good functionality that, hopefully, improves over time. Often and vexingly, even that's not always true....

If we mess up, we just fresh install--it's not nearly as involved as Windoze install. We don't tear our hair out--these guys act as if it's the end of the world. On the other hand, I shouldn't crucify great volunteers who have bent over backwards to be helpful. As for fixing Linux, often it's not "intuitive." Good docs and books are really helpful; with Windoze, I think that many of us agree that one can simply learn as one goes--generally, books aren't much help. Most programs involve clicking, simple menus, and even video tutorials.

I guess the place for this rant is my own blog. I'll start that up. Thanks for letting me vent. I do think a lot of people involved with UNIX relate to this.

Test captcha.

Fedora Core 5 Installation Guide

2006-06-14T17:22:50Z

65.67.98.193: /* Installation */

*Note: You must have your "kernel-devel-[version]" RPM package installed prior to fglrx installation.
*Note: The administrator of this wiki uses FC5 on a Radeon 9700 with the latest driver without any issues using the Official ATI Binary Installer.
RedHat's developers [http://www.redhat.com/archives/rhl-devel-list/2006-February/msg01178.html comments on 3rd party installers].

==livna.org package==
#Enable the livna repository
#Install the drivers and kernel module

<code>rpm -ivh http://rpm.livna.org/livna-release-5.rpm</code>
<code>yum install kmod-fglrx</code>

Notes:
* For ease of installation and updating, the package name of the driver has been changed
* As of today (2006-04-08) livna is still working out install bugs ( [http://bugzilla.livna.org/show_bug.cgi?id=842 Bugtracker] ) in the X86_64 package. It apperas they have fixed the problem, but have not yet finished testing. Some people report mixed success compiling from the source RPMS. YMMV.
* As of today (2006-06-14) tried several times to install the driver for ATI RADEON X700. It installed but not working. Still stuck at vesa. Those who are trying this method, be warned. RedHat's developer is right. It such a waste of time.

==Official ATI Binary installer==
===Pre-installation===
Update your kernel, kernel-devel, and xorg packages to the very latest before installation.
===Installation===
#Download the latest [[:Category:Releases|release]].
#su to root in init level 3 (No X server running)
# sh ati-driver-installer-[version].run
#Follow the prompts and it will install.

===Post-Installation===
#Run the <code>aticonfig --initial</code> command if you have not updated your X.org configuration file (xorg.conf).
#Change back to run level 5. <code> init 5</code>

==RPM installer==
No longer supported as Fedora Core 5 is shipping with X.org version 7.0.

[[Category:Installation Documentation]]

Fedora Core 5 Installation Guide

2006-06-14T17:21:37Z

65.67.98.193:

*Note: You must have your "kernel-devel-[version]" RPM package installed prior to fglrx installation.
*Note: The administrator of this wiki uses FC5 on a Radeon 9700 with the latest driver without any issues using the Official ATI Binary Installer.
RedHat's developers [http://www.redhat.com/archives/rhl-devel-list/2006-February/msg01178.html comments on 3rd party installers].

==livna.org package==
#Enable the livna repository
#Install the drivers and kernel module

<code>rpm -ivh http://rpm.livna.org/livna-release-5.rpm</code>
<code>yum install kmod-fglrx</code>

Notes:
* For ease of installation and updating, the package name of the driver has been changed
* As of today (2006-04-08) livna is still working out install bugs ( [http://bugzilla.livna.org/show_bug.cgi?id=842 Bugtracker] ) in the X86_64 package. It apperas they have fixed the problem, but have not yet finished testing. Some people report mixed success compiling from the source RPMS. YMMV.
* As of today (2006-06-14) tried several times to install the driver for ATI RADEON X700. It installed but not working. Still stuck at vesa. Those who are trying this method, be warned. RedHat's developer is right. It such a waste of time.

==Official ATI Binary installer==
===Pre-installation===
Update your kernel, kernel-devel, and xorg packages to the very latest before installation.
===Installation===
#Download the latest [[:Category:Releases|release]].
#su to root in init level 3 (No X server running)
#./ati-installer-(version).run
#Follow the prompts and it will install.

===Post-Installation===
#Run the <code>aticonfig --initial</code> command if you have not updated your X.org configuration file (xorg.conf).
#Change back to run level 5. <code> init 5</code>

==RPM installer==
No longer supported as Fedora Core 5 is shipping with X.org version 7.0.

[[Category:Installation Documentation]]

Fedora Core 5 Installation Guide

2006-06-14T17:21:16Z

65.67.98.193:

*Note: You must have your "kernel-devel-[version]" RPM package installed prior to fglrx installation.
*Note: The administrator of this wiki uses FC5 on a Radeon 9700 with the latest driver without any issues using the Official ATI Binary Installer.
RedHat's developers [http://www.redhat.com/archives/rhl-devel-list/2006-February/msg01178.html comments on 3rd party installers].

==livna.org package==
#Enable the livna repository
#Install the drivers and kernel module

<code>rpm -ivh http://rpm.livna.org/livna-release-5.rpm</code>
<code>yum install kmod-fglrx</code>

Notes:
* For ease of installation and updating, the package name of the driver has been changed
* As of today (2006-04-08) livna is still working out install bugs ( [http://bugzilla.livna.org/show_bug.cgi?id=842 Bugtracker] ) in the X86_64 package. It apperas they have fixed the problem, but have not yet finished testing. Some people report mixed success compiling from the source RPMS. YMMV.
* As of today (2006-06-14) tried several times to install the driver for ATI RADEON X700. It installed but not working. Still stuck at vesa. Those who are trying this method, be warned. RedHat's developer is right. It such a waste of time.

==Official ATI Binary installer==
===Pre-installation===
Update your kernel, kernel-devel, and xorg packages to the very latest before installation.
===Installation===
#Download the latest [[:Category:Releases|release]].
#su to root in init level 3 (No X server running)
#./ati-installer-(version).run
#Follow the prompts and it will install.

===Post-Installation===
#Run the <code>aticonfig --initial</code> command if you have not updated your X.org configuration file (xorg.conf).
#Change back to run level 5. <code> init 5</code>

RedHat's developers [http://www.redhat.com/archives/rhl-devel-list/2006-February/msg01178.html strongly recommend against using the install package provided by ATI]. It's sloppy install methods can render X unstable or even unusable even after uninstalling.

==RPM installer==
No longer supported as Fedora Core 5 is shipping with X.org version 7.0.

[[Category:Installation Documentation]]

Fedora Core 5 Installation Guide

2006-06-14T17:20:01Z

65.67.98.193: /* Installation */ spam

*Note: You must have your "kernel-devel-[version]" RPM package installed prior to fglrx installation.
*Note: The administrator of this wiki uses FC5 on a Radeon 9700 with the latest driver without any issues using the Official ATI Binary Installer.

==livna.org package==
#Enable the livna repository
#Install the drivers and kernel module

<code>rpm -ivh http://rpm.livna.org/livna-release-5.rpm</code>
<code>yum install kmod-fglrx</code>

Notes:
* For ease of installation and updating, the package name of the driver has been changed
* As of today (2006-04-08) livna is still working out install bugs ( [http://bugzilla.livna.org/show_bug.cgi?id=842 Bugtracker] ) in the X86_64 package. It apperas they have fixed the problem, but have not yet finished testing. Some people report mixed success compiling from the source RPMS. YMMV.
* As of today (2006-06-14) tried several times to install the driver for ATI RADEON X700. It installed but not working. Still stuck at vesa. Those who are trying this method, be warned. RedHat's developer is right. It such a waste of time.

==Official ATI Binary installer==
===Pre-installation===
Update your kernel, kernel-devel, and xorg packages to the very latest before installation.
===Installation===
#Download the latest [[:Category:Releases|release]].
#su to root in init level 3 (No X server running)
#./ati-installer-(version).run
#Follow the prompts and it will install.

===Post-Installation===
#Run the <code>aticonfig --initial</code> command if you have not updated your X.org configuration file (xorg.conf).
#Change back to run level 5. <code> init 5</code>

RedHat's developers [http://www.redhat.com/archives/rhl-devel-list/2006-February/msg01178.html strongly recommend against using the install package provided by ATI]. It's sloppy install methods can render X unstable or even unusable even after uninstalling.

==RPM installer==
No longer supported as Fedora Core 5 is shipping with X.org version 7.0.

[[Category:Installation Documentation]]

Fedora Core 5 Installation Guide

2006-06-14T17:19:06Z

65.67.98.193:

*Note: You must have your "kernel-devel-[version]" RPM package installed prior to fglrx installation.
*Note: The administrator of this wiki uses FC5 on a Radeon 9700 with the latest driver without any issues using the Official ATI Binary Installer.

==livna.org package==
#Enable the livna repository
#Install the drivers and kernel module

<code>rpm -ivh http://rpm.livna.org/livna-release-5.rpm</code>
<code>yum install kmod-fglrx</code>

Notes:
* For ease of installation and updating, the package name of the driver has been changed
* As of today (2006-04-08) livna is still working out install bugs ( [http://bugzilla.livna.org/show_bug.cgi?id=842 Bugtracker] ) in the X86_64 package. It apperas they have fixed the problem, but have not yet finished testing. Some people report mixed success compiling from the source RPMS. YMMV.
* As of today (2006-06-14) tried several times to install the driver for ATI RADEON X700. It installed but not working. Still stuck at vesa. Those who are trying this method, be warned. RedHat's developer is right. It such a waste of time.

==Official ATI Binary installer==
===Pre-installation===
Update your kernel, kernel-devel, and xorg packages to the very latest before installation.
===Installation===
#Download the latest [[:Category:Releases|release]].
#su to root in init level 3 (No X server running)
#./ati-installer-(version).run
#Follow the prompts and it will install.

Tried this method, it did not work.

===Post-Installation===
#Run the <code>aticonfig --initial</code> command if you have not updated your X.org configuration file (xorg.conf).
#Change back to run level 5. <code> init 5</code>

RedHat's developers [http://www.redhat.com/archives/rhl-devel-list/2006-February/msg01178.html strongly recommend against using the install package provided by ATI]. It's sloppy install methods can render X unstable or even unusable even after uninstalling.

==RPM installer==
No longer supported as Fedora Core 5 is shipping with X.org version 7.0.

[[Category:Installation Documentation]]