Ubuntu Intrepid Installation Guide

Installation Guide for Ubuntu Intrepid (v 8.10)

The three alternatives

ATI has a bad track-record when it comes to drivers for Linux. There are countless stories about black screens, hours of configuring X, installing drivers and swearing at the computer. AMD has traditionally been a bit more Linux-friendly, so after AMD bought ATI, there has arised a slight hope for better drivers for ATI-cards on Linux.

However, creating better drivers takes some time, so while the people at AMD are doing their thing, people with ATI cards basically have these options:

1. Use the open source drivers. These are stable and nice, but currently they have poor 3D-performance, if any. If that's not a problem, they are the Right Choice (tm).
2. Use the restricted-driver management system that comes with Ubuntu to install the drivers (envy/jocky/"restricted" packages).
3. Install the drivers manually. This should be your last resort, and may not even work.

The open source drivers

By default, one of the open source drivers are used. If this works for you, you don't need to change anything.

These comes with the X.org X server:

• vesa
• ati
• radeon
• radeonhd

The "ati" driver will automatically choose the best driver for your video card. There is no need to change it from "ati" or even create an xorg.conf file in most cases. The xorg.conf file is being deprecated.

Installing the restricted drivers "the Ubuntu way"

Restricted Drivers Manager

For most users it won't be necessary to go into installation and configuration details of the driver. Ubuntu 8.10 (Intrepid) provides a notification saying that there are restricted drivers available. You just have to go there (Restricted Drivers Manager) and enable the "ATI accelerated graphics driver". Ubuntu will then install and configure the driver for you. If this does not provide the optimal solution you were looking for, please read ahead.

Installation

Just use the hardware manager on the system menu (jocky-gtk), or this:

This will install the current driver in Ubuntu's repository. It is older than the one AMD has released, but will be supported by Ubuntu. Note that there are different version-numbers for Catalyst itself and the amdccle program that comes with Catalyst!

Terminal Command

$ sudo apt-get update $ sudo apt-get install linux-restricted-modules-generic restricted-manager $ sudo apt-get install xorg-driver-fglrx $ sudo depmod -a

The second line may not be necessary as you may already have restricted modules installed. Run it just in case. If the third line fails, you probably don't have the restricted repository enabled. See Pre-Installation.

After this, you may need to edit Xorg.conf:

Terminal Command

$ sudo gedit /etc/X11/xorg.conf

In the device section, if it is not already there add:

File: /etc/X11/xorg.conf

Driver "fglrx"

Then to make sure Xorg is set up correctly, you'll have to let aticonfig "initialize" it:

Terminal Command

$ sudo aticonfig --initial -f

aticonfig must be used every time you change xorg.conf!

After this you should be able to restart your computer and have the driver working. To test type

Terminal Command

$ fglrxinfo

into a terminal. If the vendor string is not ATI, but Mesa, check #Removing Mesa drivers

Post-Installation Tweaks

To enable hardware accelerated video on pre-R500 cards, edit /etc/X11/xorg.conf to include the following lines without [...]

Section "Device"
	[...]
	Driver		"fglrx"
	Option		"VideoOverlay"	"on"
	Option		"OpenGLOverlay"	"off"
	[...]
EndSection

Note that when Visual Effects (Compiz) are active, flickering and artifacts may occur in OpenGL applications and hardware accelerated video windows (particularly with R300 chipset). To prevent this, disable Visual Effects.

Installing the restricted drivers manually

If you are using the x86_64 architecture (64 bit), be sure to inst "ia32-libs" before proceeding!

Make sure universe and multiverse are enabled in your repository sources.

1. Install necessary build tools.

Terminal Command

$ sudo apt-get update $ sudo apt-get install build-essential cdbs fakeroot dh-make debhelper debconf libstdc++5 dkms linux-headers-$(uname -r)

2. Download the latest Catalyst package.

Download page: Catalyst 15.12. This package contains both the 32-bit and 64-bit driver.

Open a terminal window and switch to the directory you downloaded the installer to. (Example: $ cd Desktop)

3. Create .deb packages.

Terminal Command

$ sh radeon-crimson-15.12-15.302-151217a-297685e.zip --buildpkg Ubuntu/intrepid

("intrepid" is not a typo)

4. Add driver to kernel module blacklist.

The ATI driver must be added to the kernel module blacklist so that the new ATI driver will be used. If it is not blacklisted, the official Ubuntu repository version of the ATI driver will be loaded instead.

Terminal Command

$ sudo gedit /etc/default/linux-restricted-modules-common

Add "fglrx" to the line "DISABLED_MODULES"

File: /etc/default/linux-restricted-modules-common

DISABLED_MODULES="fglrx"

Please note that after the modification above, the "Restricted Driver Manager" will signal "ATI accelerated graphics driver" not enabled (unticked). This is perfectly correct. At the end of the installation procedure it will signal in Status: "in use" (green light), but NOT enabled. It simply means that the fglrx module contained in the linux-restricted-modules package is not enabled, but another fglrx module (8.10) is in use.

You may also need to edit the file(s) (if they exist):

Terminal Command

$ sudo gedit /etc/modprobe.d/blacklist-restricted $ sudo gedit /etc/modprobe.d/blacklist-local

Put a # in front of the line "blacklist fglrx", if it is present. Otherwise, the kernel module will not load automatically, and you will not get 3D acceleration.

5. Install .debs.

Terminal Command

$ sudo dpkg -i xorg-driver-fglrx_8.542-0ubuntu1_amd64.deb fglrx-kernel-source_8.542-0ubuntu1_amd64.deb fglrx-amdcccle_8.542-0ubuntu1_amd64.deb

Using tab completion can make this command easier.

Additional 64-bit instructions

If you have a 64 bit install, the above dpkg command may complain that "Errors were encountered while processing: fglrx-amdcccle". This is because of a dependency of the amdccle package on 32 bit libraries. If you receive this error, issue the following command after the above dpkg command, which will force the installation of all of the 32 bit dependencies, and then the amdccle package:

Terminal Command

$ sudo apt-get install -f

Catalyst 15.12 on 64-bit systems requires the --force-overwrite command in the above dpkg command:

Terminal Command

$ sudo dpkg -i --force-overwrite xorg-driver-fglrx_8.542-0ubuntu1_i386.deb fglrx-kernel-source_8.542-0ubuntu1_i386.deb fglrx-amdcccle_8.542-0ubuntu1_i386.deb

Using tab completion can make this command easier.

When installing the packages, if xorg-driver-fglrx_8.542 fails to install due to a diverted file conflict, you can fix the package with this procedure. If you get problems with dkms, you can patch the temporary sources and compile them yourself: http://www.phoronix.com/forums/showthread.php?t=12546

If you can't get past these problems, consider using Hardy and just upgrading the kernel manually and installing the packages you need from Intrepid. "EnvyNG" is also an idea.

Finishing the Install: Configuration

If you've used fglrx previously, you will not need to do this.

Now you'll have to edit your xorg.conf

sudo gedit /etc/X11/xorg.conf

and add the following line to the Device section (if it does not already exist). Include the following lines without [...]:

Section "Device"
	[...]
	Driver		"fglrx"
	[...]
EndSection

Save and exit, then run

Terminal Command

$ sudo aticonfig --initial -f

in a terminal. If it does not error you should be fine.

Some people find that changes to xorg.conf don't get used by the driver. To force the ati driver to adopt changes made to xorg.conf, type the following command:

Terminal Command

$ sudo aticonfig --input=/etc/X11/xorg.conf --tls=1

Finally, reboot the computer and type

Terminal Command

$ fglrxinfo

into the terminal. If the vendor string contains ATI, you have installed the driver successfully. Release 8.8 looks like:

display: :0.0  screen: 0
OpenGL vendor string: ATI Technologies Inc.
OpenGL renderer string: Radeon X1950 Series
OpenGL version string: 2.1.7873 Release

Please note: Depending on the particular ATI card that you own, you may or may not automatically have all of the relevant driver features enabled. R500 and R600 cards (X1xxx, HD series, and newer) in particular will need TexturedVideo enabled in Xorg.conf (rather than the traditional VideoOverlay) in order to support Xv accelerated video playback.

Finally

1. Add tweaks as needed: http://ge.ubuntuforums.com/showthread.php?t=849422
2. Restart X, if it doesn't work, you can use the "vesa", "radeon" or "radeonhd" driver in the mean time, until you make it work.
3. If you downgraded X to make fglrx work: enter synaptic, make sure all packages with "xorg" and "x11" are locked so that you can update and upgrade without worries.

Done! Now run amdcccle, glxgears, warsow etc :)

Issues

Couldn't find library libfglrx_gamma.so.1

If you are having this error:

dpkg-shlibdeps: failure: couldn't find library libfglrx_gamma.so.1 needed by debian/xorg-driver-fglrx/usr/bin/fglrx_xgamma (its RPATH is '').

Fix it by doing the following:

sudo sh ati-driver-installer-8-7-x86.x86_64.run --extract driver
cd driver/arch/x86_64/usr/X11R6/lib64
sudo ln -s libfglrx_gamma.so.1.0 libfglrx_gamma.so.1
cd ../../../../../
sudo sh ati-installer.sh -- --buildpkg Ubuntu/hardy

Mesa drivers

If fglrxinfo reports that Indirect rendering by Mesa is in place, even though you have installed ATI driver, you might want to remove Mesa:

• Remove the package xserver-xgl.

sudo apt-get remove xserver-xgl

Explanation: If you installed this previously in order to make compiz work, it will not allow direct rendering on your display. You can check out if this is what it causing the problem by running

DISPLAY=:0 glxinfo | grep render

If it returns an ATI renderer, it means that xgl is being displayed indirectly on the display 1. (Taken from [1])

Warning: This might make your compiz stop working as it is configured to use XGL. A solution might be to run the Envy script in order to configure compiz. Or, if Compiz stopped working due to "Composite" problem, check that the following is set in the /etc/X11/xorg.conf

Section "Extensions"
	Option		"Composite"	"Enable"
EndSection

---

• Check for AGP and DRI errors in /var/log/Xorg.0.log like these are:

(EE) fglrx(0): [agp] unable to acquire AGP, error -1023

(EE) fglrx(0): cannot init AGP

(EE) fglrx(0): atiddxDriScreenInit failed, GPS not been initialized.

(WW) fglrx(0): * DRI initialization failed! *

If you have Intel 8285P and E7205 chipsets and AGP not detected then you have to remove the i82875p_edac module and restart a some others:

rmmod i82875p_edac
rmmod fglrx
rmmod intel-agp
rmmod agpgart
modprobe agpgart
modprobe intel-agp
modprobe fglrx

Blacklist the modules e7xxx_edac so it doesn't start up again when booting - add the following line at the beginning of /etc/modprobe.d/blacklist:

blacklist i82875p_edac

This has been known to fix issues with -Mesa -AGP -DRI -Google earth and -suspend to RAM (s2ram).

Explanation: http://openwetware.org/wiki/Computing/Linux/Ubuntu

---

• Check you are running the correct kernel.

Explanation: If you're upgrading from Gutsy to Hardy in some instances the Grub bootloader does not get updated and the new kernel is not loaded.

Run in a terminal:

uname -r

If the output starts with 2.6.22 or below you are not using the current kernel and the Ati drivers will not load properly.

If this doesn't help, try Ubuntu Gutsy Installation Guide#Verifying, or other links: [2], [3], [4].

Hang at logout

If you experience hangs when logging out (of X) it is probably due to the /etc/ati/authatieventsd.sh script looking for X authorisation files in the wrong place when it starts up. You can kill the hanging authatieventsd.sh processes from a console tty to allow the shutdown of the X server. This can be fixed permanently with:

sudo mkdir -p /var/lib/xdm/authdir
sudo ln -s /var/run/xauth /var/lib/xdm/authdir/authfiles

If that doesn't work then you can disable atieventsd with this command:

sudo /usr/sbin/update-rc.d -f atieventsd remove

Suspend/Hibernation

Suspend hibernation works with the latest driver.

For ATI X1400, to get the laptop to wake up from suspend, I had to change the following in /etc/default/acpi-support:

SAVE_VBE_STATE=false

POST_VIDEO=false 

ENABLE_LAPTOP_MODE=false

For Radeon 3200, to wake up from suspend, I had to add the following lines to /etc/X11/xorg.conf: (This settings is not good option, if you are using compiz-fusion or any other transparency-based thingie. Not working for HD 3850)

Section "Extensions"
        Option        "Composite"        "Disable"
EndSection

Section "ServerFlags"
       Option  "AIGLX" "off" 
EndSection

Can't remove fglrx with dpkg

If dpkg really-really refuses to remove an older fglrx-package, it might be needed to edit /var/lib/dpkg/diversions and remove a few lines. This sort of trickery should be avoided until you've tried absolutely everything else, though.

This module/version combo is already installed

If you get this error-message, simply uninstall the previous version before installing the new one with:

sudo dkms remove -m fglrx -v 8.522 --all